Sioux Tools 2050 Instrukcja Użytkownika

www.siouxautomation.com MON600127 12/7/04

5 OPERATION 1. Before attempting to fill the mixer, make sure that the discharge door is completely closed, the chute is in the up position, and

6 6. Proper loading procedure involves loading smaller quantity ingredients in the center of the mixer first, to cover up the mixing paddles. Th

7 8. Normal mixing time is form 1 to 2 minutes after the last ingredient has been added. It is necessary to run the MaxiMixer at 1600 ENGINE RPM

8 MAINTENANCE Your MaxiMixer will be delivered, fully lubricated and set up to all drive component installation specifications. During the break

9F. The shear sprocket uses one 5/8 X 3-1/2” NF grade 8 bolt. Any change from this specification will void warranty. POWER TAKE OFF SHAFTS G. Kee

DCBABCD1234567887654321REVISIONSREV.DATE CHKBYDESCRIPTIONECNREVDWG NO.MON600123DO NOT SCALE DRAWINGDRAWNDATECHECKEDSCALEBREAK ALL EDGES.03 X 45FRAC

WARNINGIF WORK MUST BE PREFORMED INSIDEMIXER A PROTECTIVE COVER MUST BEPLACED OVER KNIVES TO AVOID INJURYOR DEATH.ALWAYS STOP MIXER AND TURN OFFMOTOR

MaxiMixer Model 2050 Truck Mount Assembly Prints

REVISIONSECN REV. DESCRIPTION DATEBY CK2948ADEL:MON100437ADD:SPCABLETIEMED,SPCABLETIEHVY,TWHL43A,TWKIT#3,SACFLAP24X24,SAC56009,BLT516X114NC,NUT516NC,

DCBABCD12345678876543 21REVISIONSREV.DATECHKBYDESCRIPTIONECNREVADWG NO.MON900386DO NOT SCALE DRAWINGDRAWNDATECHECKEDSCALEBREAK ALL EDGES.03 X 45FRA

DCBABCD12345678876543 21REVISIONSREV.DATECHKBYDESCRIPTIONECNREVADWG NO.MON900386DO NOT SCALE DRAWINGDRAWNDATECHECKEDSCALEBREAK ALL EDGES.03 X 45FRA

DCBABCD12345678876543 21REVISIONSREV.DATECHKBYDESCRIPTIONECNREVADWG NO.MON900386DO NOT SCALE DRAWINGDRAWNDATECHECKEDSCALEBREAK ALL EDGES.03 X 45FRA

ITEM NO. QTY. PART NO. DESCRIPTION1 1 MON700592 BODY,2050,TRK,WLD2 1 MON100437 CYL,HYD,2,10,PAINTED3 2 MON100450 ARM,LINKAGE,DOOR4 1 MON100831 GA,DOOR

DCBABCD1234567887654321REVISIONSREV.DATECHKBYDESCRIPTIONECNREVCDWG NO.MON900382DO NOT SCALE DRAWINGDRAWNDATECHECKEDSCALEBREAK ALL EDGES.03 X 45FRAC

NOTE:1.) CUT GREASE TUBE LENGTH TO SUIT AND RUN TUBING TO THE EIGHT BEARINGS INSIDE THE OILBATH AT ASSEMBLY. GREASE ZERKS ON BEARINGS TO B

DCBABCD1234567887654321REVISIONSREV.DATECHKBYDESCRIPTIONECNREVCDWG NO.MON900382DO NOT SCALE DRAWINGDRAWNDATECHECKEDSCALEBREAK ALL EDGES.03 X 45FRAC

DCBABCD1234567887654321REVISIONSREV.DATE CHKBYDESCRIPTIONECNREVDWG NO.MON900394DO NOT SCALE DRAWINGDRAWNDATECHECKEDSCALEBREAK ALL EDGES.03 X 45FRAC

WARNINGIF WORK MUST BE PREFORMED INSIDEMIXER, A PROTECTIVE COVER MUSTBE PLACED OVER KNIVES TO AVOIDINJURY OR DEATH. ALWAYS STOP MIXER AND DISCONNECTPO

DCBABCD1234567887654321REVISIONSREV.DATE CHKBYDESCRIPTIONECNREVADWG NO.MON900383DO NOT SCALE DRAWINGDRAWNDATECHECKEDSCALEBREAK ALL EDGES.03 X 45FRA

DCBABCD1234567887654321REVISIONSREV.DATE CHKBYDESCRIPTIONECNREVBDWG NO.MON900373DO NOT SCALE DRAWINGDRAWNDATECHECKEDSCALEBREAK ALL EDGES.03 X 45FRA

TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS MANUAL IS USED TO CALL YOUR ATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY AND TH

DCBABCD1234567887654321REVISIONSREV.DATE CHKBYDESCRIPTIONECNREVBDWG NO.MON900374DO NOT SCALE DRAWINGDRAWNDATECHECKEDSCALEBREAK ALL EDGES.03 X 45FRA

SEE NOTE 2NOTE:1.) APPLY A THIN FILM OF GEASE BETWEEN THE SHEAR HUB AND SPROCKET AT ASSY.2.) THE BRONZE BUSHING IS TO BE PRESS FIT INTO THE S

DCBABCD1234567887654321REVISIONSREV.DATE CHKBYDESCRIPTIONECNREV-DWG NO.MON900377DO NOT SCALE DRAWINGDRAWNDATECHECKEDSCALEBREAK ALL EDGES.03 X 45FRA

1 SCAL50171 LED,LAMP,12VDC15 3 SCASPSTSC SWITCH,TOGGLE,SPST,ON/OFF16 4 SPMB832X34SSP SCREW,MACH,8-32,3/4,SS17 1 STI200109 BOX,CNTRL,ELEC18 1 STI610809

DCBABCD1234567887654321REVCDWG NO.SCA170079DO NOT SCALE DRAWINGDRAWNDATECHECKEDSCALEBREAK ALL EDGES.03 X 45FRACTIONAL 1/32 3 PLACE .0

SAFETY ALERT SYMBOL − THE SAFETY ALERT SYMBOL IS USED TO PINPOINT CHARACTERISTICS WHICH IF NOT PROPERLY FOLLOWED CAN CREATE A SAFETY HAZARD. −

ABCDPROPERTY OF:SCALE SIZEDWG. NO.AREV.MATERIALDIMENSIONS ARE IN INCHESTOLERENCES UNLESS SPECIFIEDDO NOT SCALE DRAWING12345678CHAIN,COUP,DISABCD12

SAFETY FIRST FARM AND INDUSTRIAL EQUIPMENT INSTITUTE SAFETY ALERT SYMBOL. This symbol is used preceding all CAUTION (a general safety reminde

DCBABCD1234567887654321REVISIONSREV.DATE CHKBYDESCRIPTIONECNREVBDWG NO.MON700230DO NOT SCALE DRAWINGDRAWNDATECHECKEDSCALEBREAK ALL EDGES.03 X 45FRA

GENERAL SPECIFICATIONS 2050 TRUCK MOUNT WIDTH: MIXING CHAMBER...86” (218 cm) OVERALL...

TABLE OF CONTENTS PAGE INTRODUCTION 2 SET-UP 3 - 4 OPERATION 5 -7 MAINTENANCE 8 - 9 Chains Power Take Off Shafts

2INTRODUCTION Thank you for purchasing a 2050 MaxiMixer. The purpose of the MaxiMixer is to give the agricultural industry the ability to incorpor

3USING YOUR MaxiMixer READ CAREFULLY SETUP 1. When you are delivered your new MaxiMixer from the factory, it is not immediately necessary to ch

4 4. The MaxiMixer has also been supplied to you with a complete scale system. Read and understand the scale manual and familiarize yourself with it